Setting up A Bathtub
Or Book Technician HereIn this article down the page you will find some dependable information involving How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the job can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified on your own for the work and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This write-up will certainly help you set up a new tub in your restroom if you have already bought a new bathtub and also do not need to alter the plan of your previous water pipes.
Your tools and also material list ought to make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before proceeding to fit the new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The previous type ought to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Tub
Utilizing the two wooden boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the level checks out level.
To mount taps, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water as well as check all joints and also new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait till the tub has been utilized at least when as this will certainly settle it right into its final setting.
Preparing for the Setup
To start with, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, causing the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with dampness and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can break fairly very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very involved in How to Install a Bathtub Yourself and I am praying you appreciated our blog post. In case you appreciated our blog post kindly make sure you remember to pass it around. Thanks for your time invested reading it.
Set An Appointment